12/20/2023 0 Comments Battery guard by intellitec![]() ![]() ![]() If you have anyĭoubts about these techniques or instructions consult with someone BEFORE you connect a wire or cut a hole. It is assumed the installer has basic skills in electrical wiring, mechanics, and carpentry. These instructions contain all the information needed to help you install the Battery Disconnect. The new product monitors the voltage of two battery sources and automatically links them when charging is available and required. We decided to make all the parameters of. Intellitec Products, LLC introduced the Integrated RV-C based Bi-directional Isolation Relay Disconnect (B.I.R.D.) this week. Using all the feedback we have been provided from our customer base, we began the design of the Battery Guard 3000. The system operates by constantly monitors the available battery power when the engine or charging source is turned off. Specifications: Actuation Current: 5. Introducing the Battery Guard 3000 from Intellitec LLC Battery Guard 3000 is a fully programmable power management system and is available in 12V & 24V and in 100A & 250A variations. It is installed between the two batteries, connecting them together for charging and aiding in starting when the chassis batteries are low. This 12V Isolator Relay provides a simple, reliable, and cost effective means of isolating two battery systems. The Battery Guard® 1000 has a mounting plate attached with two mounting holes located in the back and uses automotive standard connectors for peripheral connections.ġ) Prevent unwanted discharging of batteries during extended periods of storage.Ģ) Safely disconnect 12 Volt electrical system when storing for extended periods.ģ) Prevent overcharging of batteries if RV is plugged into shore power for extended periods. The sales of Battery Guard 2000 over ten years provided Intellitec with very significant feedback with regards to the development of the next addition to the range of Battery Guard systems. Intellitec Big Boy Relay 00-00507-512 IN-STOCK. With its unique all in one design, Intellitec brought the electronics to the source, eliminating additional wiring and simplifying the The Battery Guard® 1000 was designed to make installation simple. Intellitec Part 00-00507-524 Sea Ray uses these on batteries and bow thruster systems. Note: If the user chooses to disconnect the system manually, the Battery Guard® 1000 will not automatically reconnect if it senses charging.Intellitec 0153‐01118‐200 Battery Guard 1000 12 Volt Heavy duty 24 volt solenoid/latching relay/disconnect. Battery Guard 2000 also acts as a manual battery disconnect system, press and hold the dahs mounted reset switch for three seconds and the batteries will be. Keep in mind, the device has a built‐in state change delay of 5 seconds to prevent constant cycling of the disconnect. The Battery Guard® 1000 will switch states. Simply push and release the pushbutton and This switch allows user control to manual disconnect or reconnect the system loads at the user’s discretion. The Battery Guard® 1000 accepts a momentary switch input signal. This condition usually occurs when a charging device is connected to the battery orĬonnecting and Disconnecting the System Loads If the Battery Guard 1000® senses a charging potential for a specified duration of time, then it will automatically reconnect the system load. C 28.41 previous price C 28.41 previous price C 28.41 + C 12.55 shipping + C 12.55 shipping + C 12.55 shipping. Split Charging Relay Heavy Duty 200 Amp 12 Volt Camper Van Motor Home T3 T4 Etc. Free shipping Free shipping Free shipping. When the voltage drops below the low voltage threshold for a specified duration of time, the Battery Guard® 1000 will automatically disconnect the battery from the system load, protecting the battery from excessive discharge. Intellitec 00-00629-120 Battery Isolator Relay Delay INVERTERS CHARGERS ISOLATO. The Battery Guard® 1000 constantly monitors the voltage level of the battery to determine the level of charge. Battery Guard 2000 constantly monitors the voltage level on the battery to determine the level of charge. This may happen if a light or an other accessory is left on for long periods of time. Optional Fastener Kit Contents: 2 Each 5/16-24 Nuts 2 Each 5/16 Lock Washers 2 Each 10-32 K-Lock Nuts Cost: 0. The Battery Guard® 1000 provides a solution for protecting your batteries from discharging to a level that might damage your batteries or to a level that prevents the vehicle from being started. Battery Guard system is intended to be used in vehicles to prevent the battery from inadvertently being discharged by some unwanted load. Intellitec Battery Guard Relay 01-00335-000.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |